Single Beam Hologram
Tutorial

Presents:

Holography Helpers

Making Single Beam Reflection Holograms

By Jason Sapan / Holographic Studios


Search for a Holography book. Enter the keyword Holography.

  Search by: 

The simplest hologram is a single beam reflection hologram. It can be seen in white light. It can be made with a small 5 milliwatt (mw) Helium-Neon (He-Ne pronounced he-knee) laser (producing a continuous red beam), a 10 to 20 power (10x - 20x) microscope objective (lens) and some holographic film. You can use a less powerful laser but you will need to make your exposure time longer. And of course if you have a more powerful laser you should shorten your exposures. Lasers that are polarized have more useful power for making holograms. Make sure that the laser is rated TEM 00, this means that when you spread the beam out with a lens there will be no dark spots. For instance TEM 01 would produce a beam with a black hole in its center and is referred to as the donut mode. TEM stands for Transverse Electromagnetic Mode, and the two numbers following are the graphic cartesian coordinates of holes in the beam. Always excercise care in using a laser. Do not point it at anyone or look directly into it.

You will need a simple darkroom with a dark green safelight with a 20 watt or less bulb at least 8 feet from the film. You need at least 3 developing trays, holographic developer (consult with the people you purchase the holographic film from), a good holographic bleach, and a tray with water and a half a capful of Kodak Photo-Flo as a final anti spotting bath. You also need a sink. A bathroom is okay if nothing else is available. Just make sure it is light tight. You should test the safelight by placing a small piece of your holographic film out where you do your developing for about 10 to 15 minutes. Develope it and see if it is exposed by the safelight. If it is then you need more green on your filter or less light. A dimmer switch on the light can help.

The 5 mw He-Ne laser will cost around $100 - $200 US from Meridith Instruments or MWK (on the web). A microscope objective is cheap. And film costs around $5 for a glass plate. Actual plastic film costs a bit less. Plastic film on a roll is cheapest but you have to buy a lot at once. Glass plates are considered best and are easiest to use. Developing and bleach formulas are available from the people who sell you the film. Try Geola Labs or Integraph on the web.

This is the way I make single beam reflection holograms. Remember, there are many other ways to make this or any type of hologram. Feel free to experiment with the geometry.

If you can, make an isolation table for your hologram set up. However, it is not essential for a successful exposure, but it will help you obtain brighter holograms in a noisy environment. An isolation table can be as simple as floating a slab of granite, marble, or 1/4 inch thick steel on an inner tube. This acts as a shock absorber. Some people make a sandbox and float that on the inner tube. The table top should be rectangular at least 3 feet by 4 feet. Longer is better than wider. You can also work on a hard top table or a concrete floor.

Aim the laser through the lens. This will spread the beam out like a flashlight. This beam of light is called the "reference beam". At a distance of about a meter or so from the lens mount the holographic film. Mount the film at a 30 to 45 degree angle to the beam. This will be the "reference angle" you will use when you are lighting the completed hologram and are viewing it. Once you have aligned these elements you should secure them in place so they don't move. You can sandwich the film between two pieces of quarter inch thick glass using carpenter's spring clamps. Glue the bottom rear back edge of the back plate of glass to the table top with hot glue available from a crafts or hardware store. Get a hot glue gun with a trigger feed. Make sure that the glue is only on the back edge. Do not touch the hot glue after it comes out of the gun. It is very hot and can cause serious burns. Wait till it cools in about a minute or so and has hardened. To remove it after it cools you can wet it with a little acetone to help break its bond.

If you are shooting glass plates you will need to make a glass plate holder. A pair of "U" channel metal rods can be glued to a bottom and top support bar so that the plate can slide down into it to the table. This holder should be hot glued to the table with buttress supports from the top of both "U" channels to the table top. The plate holder can be made of hard wood that has had grooves routed out as well. You can use some modeling clay in each corner of the plate to prevent it from moving after you slide it into the channels. The plate and object are mounted sideways. I suggest that you paint all surfaces and plate holders flat black to prevent any unwanted light from degrading the quality of your hologram.

The laser light reflecting off the object is called the "object beam". It then bounces back through the holographic film where it meets the "reference beam". The two beams pass through each other creating an "interference pattern". This interference pattern is what you are photographing on the holographic film.

Mount your object sideways with the top of the object nearest to the laser, directly behind the glass ( the opposite side of the glass than the laser). It helps to actually have it touch the glass. The laser beam will "reflect" off the object. I like to use objects that are not too deep. A good beginner's image is coins. The choice of your object is critical to your success. The object must be very solid. Metal, ceramic, seashells, plaster, or stone are good. Paper, plastic, feathers, string are very tempermental and are not for your first attempts since they are more prone to vibration problems that might tend to ruin your exposures. The object should be colored white, red, gold, or another light color. Black, green, or blue will disappear in a hologram so do not use objects made exclusively of them. However these colors can be used as long as they are within light colors. Remember the laser is shining red light on your object. The color red next to the color white on your object will all look like a single color. Red print on a white background will disappear. Try viewing your object through a red filter to get a good idea of how it will look in laser light. You can use hot glue to adhere them to another plate of glass that you press up against the back plate (the far side) of the glass being used as your film holder. You can use more than one layer of glass plate model holders for more depth. You must glue the bottom of each model holding plate to the table surface. I like to also take wooden or metal rods and glue them at an angle from the top of each plate of glass to the table top as a flying buttress. This helps eliminate vibration problems that would cause the hologram to be dim or not work at all. The sturdier you secure the model and plate holder the more likely it is that your hologram will be successful.

Before you load holographic film you must now take a piece of black cardboard and lean it up against the front of the laser as a "shutter" to stop the beam of laser light from reaching the film holder.

Now take a piece of film and in the dark put a corner of it between your lips. The side that sticks to your lips is the emulsion. Place that side toward the object (i.e. the coins) and place the front plate of glass over the film and clamp it to the back plate with the spring clamps. I use three clamps. One on each side and one on the top. Now walk out of the room for at least 20 minutes. This allows the "camera" you have just made to "settle" and prevent vibration problems. Remember light waves are incredibly small. It takes very little to move them.

Come back in the room and walk next to the shutter. Wait one minute then lift the "shutter" for about 15 seconds. Close the shutter. You might want to do a bracket exposure. In this process you cover three quarters of the film with a black card. After you have exposed the first quarter of the film you slide the black card back to allow the next quarter of the film to be exposed. Wait a minute for the system to settle and expose the film for an additional 5 seconds. Then you replace the shutter and move the black card back once again to allow another quarter of the film to be exposed. After you wait another minute to allow the film to settle again, open the shutter for yet another 5 seconds. Finally, you remove the black card completely, wait another minute, and expose a final 5 seconds. (After you develope the film you will be able to see which amount of exposure time worked best. You can then adjust future exposures sucessfully.) Take the film out from between the glass plates and develope it in your darkroom. If the darkroom is far from the film you might want to transport it there in a light proof box. Follow the procedure of development that the film manufacturer gives you. Generally, you will develope the film until it is black and then bleach it clear and wash it. I suggest you wear latex gloves and wear an apron or lab jacket. Make sure the darkroom is well ventilated. It is now safe to turn on the room lights. You will not see an image until the film is dry. You can see rainbows through the film if you hold it up to a light. This is the diffraction from the interference pattern you have just photographed on the film. It is a good sign that your hologram has worked. While it is wet the emulsion is swollen and thereby visible only to those who can see infrared light. I like to hang my holograms to dry, but you can blow dry the film in front of a fan. Don't use a hot blower. It can distort the film or start a fire.

The dry hologram is best viewed with a bright spot light (halogen is best) You can also use a clear light bulb not a frosted bulb. Do not use flourescent lighting to view holograms. It will make the image look blurry. Sunlight will work but it also will bombard the hologram with UV rays and tend to darken the film over a long period of time causing it to "print out". It will still be a good hologram, but the film will no longer be clear. Do not get the hologram wet once it has dried. It can erase the image or spot it permanently. If you do get it wet, quickly soak it in water and carefully redry it.

You may have some trouble finding the image the first time. Remember it must be lit with light coming from the same angle that it was created with (the "reference angle"). Try slowly rotating the film and turning it over until you see the holographic image. It should appear behind the film as a "virtual" image. It should look exactly the way your model was when you shot it ("orthoscopic"). If the object appears to be sideways you forgot to mount it sideways when you mounted the model. In that event its time to go back to your set up and rotate the object in your holographic camera 90 deegrees and reshoot. Now if you flip the film over the holographic image will appear to jump out in front of the film as a "real" image. This image is inside out or "pseudoscopic". It helps to have a piece of black card stock behind the film to make it easier to see.

Congratulations! You are now a holographer! Let me know how you did.

Summary:

Reflection holograms are made by interfering the reference beam with the object beam from opposite sides of the holographic film. It is visible in white light.


More Holography Helpers

GOOD VIBRATIONS

IMPRESSED WITH LIGHT

INTERFERENCE CAN STOP THINGS

FREQUENTLY ASKED QUESTIONS

 

Have A Technical Question? Ask Dr. Laser

Holohelper Index
Holographic Studios HomePage
Holograpy Catalog

 

© Holographic Studios
October, 1998